Electronics and Electrical Engineering

Alan Zhao Shanghai Jiao Tong University, China

• Foreword; Fuzzy based direct torque and flux control of induction motor drives; Coordinated frequency control of thermal units with DC system in a wind-thermal-bundled system transmitted by High Voltage Direct Current (HVDC) line; A biomedical system combined fuzzy algorithm for telemedicine applications; A preventive control method for overload in a multi-source grid; Effects of thermal annealing on the tungsten/lanthanum oxide interface; A study on the capacity optimization and allocation of wind/solar/diesel and energy storage hybrid micro-grid systems; A neural network Proportional-Integral-Differential (PID) control based on a genetic algorithm for a coupled-tank system; Research into the reactive power compensation of a new dual buck non-isolated grid inverter; Modelling condition monitoring inspection intervals; A coordinated voltage control strategy for a Doubly-Fed Induction Generator (DFIG) wind farm system; SOM-based intrusion detection for SCADA systems; Nonlinear and adaptive backstepping speed tracking control of a permanent magnet synchronous motor despite all parameter uncertainties and load torque disturbance variation; The convolution theorem associated with fractional wavelet transform; Robustness testing method for intelligent electronic devices; Design and analysis of quasi-optics for a millimeter wave imaging system; A simply fabricated hybrid type metal based electrode for application in supercapacitors; Joint scheduling based on users’ correlation in MU-CoMP; A monitoring system of harmonic additional loss from distribution transformers; A performance evaluation of higher order modulation considering Error Vector Magnitude (EVM) in a Long Term Evolution (LTE) advanced downlink; Research on the control method of the driving system for the in-wheel driven range-extended electric vehicle; Research on TSP based two phases path planning method for sweep coverage of a mobile wireless sensor network; A monitor method of a distribution transformer’s harmonic wave compatible to its loss; Identification of a gas-solid two-phase flow regime based on an electrostatic sensor and Hilbert–Huang Transform (HHT); A fast multilevel reconstruction method of depth maps based on Block Compressive Sensing; Dynamic modelling with validation for PEM fuel cell systems; A highly sensitive new label-free bio-sensing platform using radio wave signal analysis, assisted by magnetic beads; Noise analysis and suppression for an infrared focal plane array CMOS readout circuits; Speaker recognition performance improvement by enhanced feature extraction of vocalsource signals; Online detection and disturbance source location of low frequency oscillation; A soft-start Pulse Frequency Modulation-controlled boost converter for low-power applications; Thermal analysis of phase change processes in aquifer soils; The development of a slotted waveguide array antenna and a pulse generator for air surveillance radar; A harmonic model of an orthogonal core controllable reactor by magnetic circuit method; A risk assessment model of power system cascading failure, considering the impact of ambient temperature; Target speech detection using Gaussian mixture modeling of frequency bandwise power ratio for GSC-based beamforming; A compressive sampling method for signals with unknown spectral supports Design and analysis of SSDC (Subsynchronous Damping Controller) for the Hulun Buir coal base plant transmission system; Stage division and damage degree of cascading failure; The design of a highly reliable management algorithm for a space-borne solid state recorder; A patrol scheme improvement for disconnectors based on a logistic regression analysis; Progress on an energy storage system based on a modular multilevel converter; Robust fall detection based on particle flow for intelligent surveillance; An IEC 61850 based coordinated control architecture for a PV-storage microgrid; The design of an IED for a high voltage switch operating mechanism based on IEC 61850; A profile of charging/discharging loads on the grid due to electric vehicles under different price mechanisms; Algorithm design of the routing and spectrum allocation in OFDM-based software defined optical networks; The impact of Negative Bias Temperature Instability (NBTI) effect on D flip-flop; The electrical property of a three dimensional graphene composite for sensor applications; A method of automatically generating power flow data files of BPA software for a transmission expansion planning project; The analysis of training schemes for new staff members from substation operation and maintenance departments; Research of source-grid-load coordinated operation and its evaluation indexes in AND; Progress on the applications of cascaded H-bridges with energy storage systems and windpower integrated into the grid; Aluminium alloy plate flaw sizing by multipath detection; An equilibrium algorithm clarity for the network coverage and power control in wireless sensor networks; Three-layer architecture based urban photovoltaic (PV) monitoring system for high-density,multipoint, and distributed PV generation; Modelling and estimation of harmonic emissions for Distributed Generation (DG); Mechanism and inhibiting methods for cogging torque ripples in Permanent Magnet Motors; Content-weighted and temporal pooling video quality assessment; A filter structure designing for an EAS system; A mini-system design based on MSP430F249; A control system for the speed position of a DC motor; Intelligent wireless image transmission system; Model predictive control for a class of nonlinear systems via parameter adaptation; Control strategy of BESS for wind power dispatch based on variable control interval; A study of the maintenance of transformer using a cost-effectiveness optimization model; A new decision support system for a power grid enterprise overseas investment; A coal mine video surveillance system based on the Nios II soft-core processor; Research on a mechanism for measuring force in material moulding and the features of its measuring circuits