Blends of Natural Rubber

Novel Techniques for Blending with Specialty Polymers

Inbunden, Engelska, 1997

AvK.C. Jones,Andrew Tinker,K. C. Jones

2 019 kr

Beställningsvara. Skickas inom 10-15 vardagar. Fri frakt för medlemmar vid köp för minst 249 kr.

Finns i fler format (1)

Häftad

1 999 kr

Skickas inom 10-15 vardagar

Blends of natural rubber with speciality synthetic rubbers, such as Nitrile Rubber and Ethylene Propylene Rubbers have in the past failed to combine the best properties of polymers. This work contains the results of an ongoing research programme funded by the "Common Fund for Commodities" (CFC) where blending techniques have developed which enable high quality blends to be produced, optimizing the properties of two polymers. This development has reached the stage of field trials with products based on these blends. This book should be of interest to the rubber industry, rubber technologists, polymer technologists and professors, materials science specialists, graduate students, lecturers and teachers.

Produktinformation

Utgivningsdatum1997-12-31
Mått155 x 235 x 20 mm
Vikt582 g
FormatInbunden
SpråkEngelska
Antal sidor256
Upplaga1998
FörlagChapman and Hall
ISBN9780412819407

Tillhör följande kategorier

1 Introduction — the book and rubber blends.- 1.1 Sources of problems — and solutions.- 1.2 Blends considered.- 1.3 Strategy.- 1.4 Wider implications.- 2 Measurement of crosslink density in vulcanized blends.- 2.1 Swollen-state NMR spectroscopy.- 2.2 Network visualization microscopy.- 2.3 References.- 3 Characterization of vulcanized blends by microscopy.- 3.1 Introduction.- 3.2 Light microscopy.- 3.3 Scanning electron microscopy.- 3.4 Chemical staining.- 3.5 Chemical etching.- 3.6 Transmission electron microscopy.- 3.7 SEM-based scanning transmission electron microscopy.- 3.8 Conclusion.- 3.9 References.- 4 Estimation of crosslink density by solid-state NMR spectroscopy.- 4.1 Introduction.- 4.2 Experimental procedures.- 4.3 NMR spectra of NR.- 4.4 NMR spectra of other rubbers.- 4.5 Conclusion.- 4.6 References.- 5 NR/NBR blends — basic problems and solutions.- 5.1 Introduction.- 5.2 NR/NBR41.- 5.3 NR/Krynac 34.50 blends.- 5.4 Conclusion.- 5.5 References.- 6 Improving the morphology and properties of NR/NBR blends with NR/PMMA graft copolymers.- 6.1 Introduction.- 6.2 Methods of blending.- 6.3 Phase morphology.- 6.4 Physical properties.- 6.5 Crosslinking density distribution in the blends.- 6.6 Conclusions.- 6.7 References.- 7 Improving the morphology and properties of NR/NBR blends with polychloroprene as the compatibilizing agent.- 7.1 Introduction.- 7.2 Cure systems for NR/CR/NBR blends.- 7.3 Phase morphology of NR/CR/NBR blends.- 7.4 Conclusions.- 7.5 References.- 8 NR/NBR blends — compounding for food contact applications.- 8.1 Introduction.- 8.2 Formulations for milking inflations to meet FDA regulations.- 8.3 Formulations for milking inflations to meet BGA regulations.- 8.4 Conclusion.- 8.5 References.- 9 Novel natural rubber/ethylene propylene copolymer(EPM) blends.- 9.1 Introduction.- 9.2 Dynamic vulcanization.- 9.3 Selection of dynamic cure system.- 9.4 Dynamic vulcanization of NR/EPM blends.- 9.5 The sandwich mix cycle.- 9.6 Processing behaviour.- 9.7 Vulcanization of DV blends.- 9.8 Resistance to environmental damage.- 9.9 Preferred formulation.- 9.10 Conclusion.- 9.11 References.- 10 Natural rubber/ENR-25 blends.- 10.1 Introduction.- 10.2 Designed experiments.- 10.3 Plasticizer investigations.- 10.4 Cure systems.- 10.5 Dynamic:static modulus ratios.- 10.6 Tri-blends.- 10.7 Conclusions.- 10.8 References.- 10.9 Appendix.- 11 Partition coefficients for an ester plasticizer in black-filled blends.- 11.1 Introduction.- 11.2 Identification of exuding plasticizer.- 11.3 Estimation of Diolpate partition coefficients.- 11.4 Conclusion.- 11.5 References.- 12 Improving resistance to low temperature crystallization in NR/ENR-25 blends.- 12.1 Introduction.- 12.2 Effect of incorporating Hv-BR into NR/ENR-25 blends.- 12.3 Curative level optimization.- 12.4 Conclusions.- 12.5 References.- 13 Compounding NR/ENR-25 and NR/Hv-BR/ENR-25 blends for engineering applications 158.- 13.1 Introduction.- 13.2 Optimizing plasticizer level and masterbatch ratio.- 13.3 Mixing trials.- 13.4 Single-stage mixing for crossblending and finalizing.- 13.5 NR/Hv-BR/ENR-25 blends.- 13.6 Injection moulding.- 13.7 Conclusions.- 13.8 References.- 14 Solutions to the basic problems of poor physical properties of NR/EPDM blends.- 14.1 Introduction.- 14.2 Approaches to improving NR/EPDM blend properties.- 14.3 Mixing procedures.- 14.4 Effect of EPDM modification on crosslink density.- 14.5 Effect of EPDM modification on phase morphology.- 14.6 Interaction of modified EPDM and carbon black.- 14.7 Physical properties.- 14.8 High temperature curing effects.-14.9 Modification of different EPDM grades.- 14.10 Conclusion.- 14.11 References.- 15 Compounding NR/EPDM blends for tyre sidewalls.- 15.1 Introduction.- 15.2 Properties of comparable NR/BR and NR/EPDM blend formulations.- 15.3 Development of a NR/EPDM sidewall formulation.- 15.4 Experimental design approach.- 15.5 Crack growth testing.- 15.6 Large-scale factory mixing trials.- 15.7 Compound extrusion and tyre building.- 15.8 Initial tyre tests.- 15.9 Analysis of initial tyre testing.- 15.10 Second factory tyre building and testing trials.- 15.11 Ozone and atmospheric weathering tests.- 15.12 Conclusion.- 15.13 References.- 16 Compounding NR/EPDM blends for light-coloured applications.- 16.1 Introduction.- 16.2 General experimental procedures.- 16.3 Preparation of blend compounds.- 16.4 Comparison of physical properties.- 16.5 Formulation development.- 16.6 Weathering and ozone testing.- 16.7 Conclusion.- 16.8 References.- 17 NR/EPDM blends for extruded profile weatherstrip.- 17.1 Introduction.- 17.2 General experimental procedures.- 17.3 Initial preparation and assessment of blend compounds.- 17.4 Small-scale extrusion trials.- 17.5 Formulation development and processing.- 17.6 Conclusion.- 17.7 References.